Różnice modeli S2000 w poszczególnych latach produkcji

Baza wiedzy

Różnice modeli S2000 w poszczególnych latach produkcji

Postprzez Element » 2008-04-01, 23:22

Różnice pomiędzy modelami 00/01 a 02/03
  • wprowadzono zmiany w ECU pomiędzy tymi modelami
  • plastikowa tylna szyba została zastąpiona nieco mniejszą szklaną szybą z możliwością odmrażania. Przycisk włączania odmrażania szyby został umieszczony po przeciwnej stronie niż przycisk tempomatu, po prawej stronie. Kształt przycisku uległ zmianie. Rama dachu została zmieniona aby dopasować się do zmiany tylej szyby.
  • Zestawy kolorów tapicerki skórzanej oraz plastików ulegly zmianie. Modele 00/01 mogły mieć kombinacje czerwono czarnego wnętrza, modele rocznika 02 mogły być cale czerwone, rocznik 03 wprowadził całkowicie niebieskie wnętrze (w zalezności od regionu - USA/Canada)
  • Skórzana pokrywa konsoli zastępuje wykładzinową pokrywę.Obrazek
  • Most przedni ma nieco zmniejszone rozmiary.
  • Dodano małe srebrne głośniczki (tweeters) na drzwi, małe kieszonki oraz klamki ze srebrnymi akcentami Obrazek
  • Dodano podwójne mocowanie dywaników do podłogi
  • Zwiększony znaczek Honda 'H' na zewnątrz pojazdu
  • Zmieniono kolor linii orotomierza na biały, dodatkowo podkreslony mocnym białym łukiem
  • Pedał podpórka (dead pedal) został zmieniony na aluminowy z gumowymi wypustkami aby pasował do pedałów sprzęgła, hamulca i gazu
  • Przykrywka do schowka w koonsooli środkowej oraz prostokątny otwór za nim zostały pokryte plastikiem z fakturą
  • Do tylnych świateł został dodany chromowany pierścień Obrazek
  • Klimatyzacja oraz ogrzewanie jest nieco silniejsze, drugi i trzeci stopień prędkości wentylatora jest bardziej efektywny
  • Audio zostało ulepszone, zwiekszona moc, posiada regulację basów/trebli/fade/balance inaczej rozwiązaną niż za pomoca jednego przycisku. Radioodtwarzacz jest srebrny zamiast czarny. Głośniki w drzwiach zostały zmienione, według użytkowników model 02/03 ma znacznie lepszy dźwięk.


Różnice pomiędzy modelami 00/03 a 04/05

  • w wersji US zmieniono kod silnika z F20C na F22C1 żeby zaznaczyć zmianę pojemności z 2.0 do 2.2 litrów.
  • w wersji rocznika 04 średnica cylindra wynosi 87mm a jego skok 90.7 mm co daje stosunek 1:1.04. W rezultacie osiągnięto większy moment obrotowy na nizszych obrotach silnika co ułatwia prowadzenia pojazdu w codziennych warunkach. W modelu 00/03 średnica cylindra wynosi 87, ale skok tylko 84mm co daje stosunek 1:0.98. Zwiekszenie mocy w F20C nastepuje po 6000 obrotów/min, natomiast w F22C powyżej 3000 obrotów/min.
  • W F22C dopływ paliwa jest odcinany przy 8000 obr/min zamiast 9000 obr/min.
  • Zmieniono przelożenia w skrzyni biegów aby zwiekszyć przyspieszenie
  • Wprowadzono znaczne zmiany zewnętrza pojazdu: zmieniono przedni zderzak, obniżono tylny zderzak ze zwiększonymi otworami na podwójną końcówkę wydechu.
  • Przednie reflektory zmieniono aby mogły zmieścić potrójne lampy zamiast podwójnych jak w modelach 00/03.
  • Tylne lampy są potrójnymi lampami LED zamiast podwójnymi klasycznymi żarówkami jak w modelach 00/03.
  • Zwiększone koła (powiększone z 16 do 17 cali) i opony nadaja agresywny wygląd i zwiększają osiągi. Felgi mają pięć podwójnych ramion, natomiast
    modele 00/03 miały pięć ramion.
  • Rozstaw tylnych kół oraz zawieszeni został zoptymalizowany, zwiekszono twardość konstrukcji nadwozia oraz osiągi hamulców.
  • Masę pojazdu zwięszono o 24 funty (11kg) do 2835 funtów (1288kg), ulepszono karoserię aby zwiększyć bezpieczeństwo i zespollić pojazd.
  • Zmieniono wyświetlacz w konsoli (wskaźniki obrotomierza, temperatury oleju oraz stanu paliwa)
  • Znaczace zmiany w drzwiach, zwiększono miejsce dla łokci. Dolne kieszonki zwiekszono co sprawiło, że stały się bardziej uzyteczne.
  • Zmieniono wygląd radioodtwarzacza dodając mozliwość dodania radia satelitarnego (XM Staellite Radio)
  • Gałka zmiany biegów ma elemety skórzane, całość dźwigni pokryta jest oryginalna skórą.
  • Zmieniono wygląd kierownicy, zwiekszono znaczek 'H', przycisk tempomatu dodano do przycisków kierownicy (wczesniej były dwa przyciski)
  • Konsola środkowa posiada aluminiowe wykończenie, ma mozliwość przytrzymania dwóch kubków na napoje, pokrywa otworu jest rozsuwana zamiast podnoszona.
Avatar użytkownika
Element
Klubowicz redliner
 
 
Posty: 1309
Dołączył(a): 2007-10-01, 07:34
Lokalizacja: Warszawa

Postprzez Lukas G » 2008-09-15, 12:33

Jeszcze jedna kwestia jak auto z za wody to tam jest posrane. Tam auto od lipca jest juz autem z nastepnego roku. Nie wiem czemu tak zrobili ale tak jest. Tzn. teraz od lipca auta sprzedawane tam, sa juz autami z 2009r i wszedzie maja tak wpisane. Pierwszy raz sie zdziwilem jak sprawdzalem samochod z 2005r a carfax mi mowi ze auto zostalo sprzedane w listopadzie 2004.

Mam jeszcze jedna zmiane, trzeba by tylko zweryfikowac czy to samo jest w AP1 po lifcie bo dane ze stanow i tycza sie zajefajnego AP2.

Przelozenia w ukladzie kierowniczym.
AP1 00-04
13.8 : 1

AP2 04-08
14.9 : 1

AP2 08+ i CR
13.8 : 1 (takie samo jak w AP1)
Obrazek
-=Lukas G=-
Avatar użytkownika
Lukas G
Klubowicz redliner
 
 
Posty: 1392
Dołączył(a): 2008-01-06, 18:26
Lokalizacja: Radomsko
Rocznik S2000: 2001
Wersja: AP1

Postprzez GS MIKE » 2009-01-25, 18:50

Różnice w reflektorach przednich


AP1 99-02 wersja europejska
Obrazek
AP1 99-02 wersja usa
Obrazek
AP1 02-04 wersja europejska
Obrazek

AP1lift i AP2 04-09 wersja europejska i USA
Obrazek

Różnice w modelach felg
Obrazek
Felga 16'' od 99 do 2002

Obrazek
Felga 16'' od 02 do 04

Obrazek
Felga 17" od 2004 do 2006

Obrazek
Felga 17" od 2006 do 2008

Obrazek
Felga 17" do 2009
Avatar użytkownika
GS MIKE
 
 
Posty: 6283
Dołączył(a): 2007-04-30, 09:50
Lokalizacja: Bielsko Biała
Rocznik S2000: 2002
Wersja: AP1

Re: Różnice modeli S2000 w poszczególnych latach produkcji

Postprzez GS MIKE » 2010-12-18, 11:32

Obrazek
Zderzak przedni AP1 wersja europejska (spryskiwacze)


Obrazek
Zderzak przedni AP2 wersja USA (brak spryskiwaczy)

Obrazek
Zderzak tył AP1 wersja europejska na prostokątną rejestrację
ze światłem przeciwmgłowym

Obrazek
Wersja usa kwadratowa rejestracja ,brak lampki


Obrazek
Zderzak tył AP2 charakterystyczne owalne wycięcia na końcówki wydechu

Obrazek
AP1 okrągła końcówka wydechu

Obrazek
AP2 eliptyczna końcówka wydechu obie wersje silnikowe

Obrazek
Lampa tył AP1 od 99 do 02 podwójna

Obrazek
Lampa tył AP1 od 02 do 04 podwójna ze srebrnymi obwódkami


Obrazek
Lampy tył AP2 od 04 do 09 potrójna z LED. W wersji USA oba białe wsteczne, w wersji europejskiej przeciwmgłowy w lewej lampie
Avatar użytkownika
GS MIKE
 
 
Posty: 6283
Dołączył(a): 2007-04-30, 09:50
Lokalizacja: Bielsko Biała
Rocznik S2000: 2002
Wersja: AP1

Re: Różnice modeli S2000 w poszczególnych latach produkcji

Postprzez insane » 2014-06-10, 18:23

Znalezione przypadkiem, bardziej szczegółowa lista :)

Model Year 2001
• Model year 2000 did not have a clock. Per Honda, it was intentionally left out due to the race car theme. It became standard equipment on 2001 model.
• Model year 2000 offered wind deflector as an option; it became standard with the 2001.
• Red floor mats became available.

Model Year 2002

• Public pressure was strong to replace the plastic rear window design with a glass window, equipped with a defroster, which became standard for 2002 model. The window is smaller in size and the top frame was redesigned to accommodate the glass.
• The UK Press release states “.. for 2002, there is a significant change in the suspension’s fine tuning. Spring rates have been increased, anti-roll bar stiffness reduced, and the gas-filled dampers (shocks) recalibrated. The changes have been made to improve steering feel and handling progression at the limit, while maintaining the response, grip and balance of the original S2000.” {All three changes would be for an understeer correction.}
• Anti-roll bars: Front & rear sway bars were reportedly changed. Originals were F: 28.2 mm (1.11") x 5.0 mm, R: 27.2 mm (1.07") x 5.3 mm. A new ‘02 owner says his measures: F: 26.11mm and R: 27.35mm.
• Springs: ‘ 02 rear springs have a new part number.
• Early stereo complaints were addressed in the 2002 model with an upgrade from 20 to 30 watts per channel and the addition of door mounted tweeters. The door speakers are blue-plastic, have no 'paper' cone, magnet is still small, but owner’s report the 2002 sounds vastly better.
• The solid aluminum shift knob could be cold as ice in winter or very hot in the sun, for the 2002 model it was changed to a combination leather and aluminum knob.
• The black interior color shade has changed to a dark grey or charcoal bluish black shade.
• The stereo has digital bass/treble/fade/bal controls. You push the right knob and set them as opposed to small black knobs that you would push to pop-out.
• The tonneau cover changed. There is only 1 clip on the each side to push in from underneath. The elastic bands straps on each side remain the same. Reportedly its easier to attach and doesn't appear to 'flap' up like previous design.
• The shade of wheels are a slightly darker silver with a little more metallic-flake.
• Heat and A/C fan are more powerful. The 2nd and 3rd fan speeds are noticeably more effective.
• A chrome ring has been added to the tail-lights.
• A metal ring has been added to the interior door panel pulls.
• The horn reportedly has a different tone.
• The plastic trim piece that outlines the dash, as well as the trapezoidal plastic plate in which the roof and hazard buttons sit, are made of a different color/finish plastic – a gray, grooved plastic rather than the bland black untextured plastic.
• The cupholder cover and trash hole behind it are textured plastic as opposed to the same untextured earlier ones.
• Interior leather and plastic colors have changed. For example, earlier Silver cars came with a combination of red and black interior. The 2002 model comes with a solid red interior (dash, doors, center storage, etc.).
• Radio design and color changed.
• It’s said to have improvements in the transmission to make it smoother and provide quieter shifts.
• The dead-pedal is now metal/rubber and matches the other pedals.
• A vinyl console cover replaces the carpet console cover.
• The buttons for the defroster and cruse-control on switches are a different shape.
• The new window defrost button is the cruise control on the right side of the steering wheel.
• There is a small subtle change in the trunk lid shape at the rear, near the trunk brake light. Reportedly this was to meet the Federal safety standard measurements.
• The tach indicator line is now white and the scale connected by a solid white arc line.
• The outside Honda badges are larger.
• A second post has been added to the carpeted floor mats to secure them.
• There is very limited cockpit storage in the race car tight confinements, so door panel net storage pockets were added for the 2002 model but they are too small for anything but perhaps a garage door opener.
• Paint color changes were made. In the US, Sebring Silver replaced Silverstone Metallic (the newer is a brighter silver). Suzuka Blue Metallic was added.
• Some interior colors were changed in 2002, for example, the red & black interior of the Silver car was changed to ‘all’ red.
• At mid-model year the banjo bolts in the engine lubrication system were upgraded from two-holes to four-holes each.

Model Year 2003

• Only change was to offer white cars with a tan interior.
• A Honda dealer says the clutch disc changed for 2003.
S2000 “Modulo” or “Factory Performance (FP)” In 2003 Honda announced that its division Honda Access Corporation, a Japan based operation that specializes in improving the look and performance of Honda company cars, will undertake the S2000. The FP team is led by Makoto Tamamura, the chief suspension engineer for the original NSX. To begin with the team will concentrate on only the handling traits for performance; engine tuning may come later. As of early 2003, USA availability is undetermined.

R&T’s early test vehicle (March 2003 issue) had 5-way adjustable suspension system, the entire double-wishbone set recalibrated, 17" wheels with Yokohama Advan TNR 215/45ZR-17s, slotted brake rotors and special brake pads.

At Willow Springs the stock S2000 lapped at 1:38.2. The Modulo did 1:37.6. The cost for picking up the extra ½ second, in Japan pricing, was $5,500.

Nothing more has been heard of this since.

Model Year 2004

(Second generation S2000).

ENGINE
To improve torque output, Honda engineers stroked the all-aluminum four-cylinder 6.7mm to deliver another 160cc of displacement and a slightly undersquare configuration. By Honda's measurement, there's still 240 hp at your command, only it arrives at 7800 rpm, some 500 rpm lower than previously delivered. This is because the increase in piston speed from the long-stroke layout would stress the internals to the breaking point at a higher rpm. It's one of those physics things.
• Redline dropped from 9000 RPMs to 8000 RPMs.
• F20C engine code changed to F22C ( 2.2 liter) in North America market; the F20C (2.0 liter) remains in production elsewhere. Reportedly Greece gets the F22C too with engine code designation F22C1.
• Through the use of a longer stroke (increased to 90.7mm from 84mm), the motor's displacement was increased from 1997cc (2.0L) to 2157 cc (2.2L).
• Basically a 500rpm shift of the horsepower curve (to the left, on the rpm scale). Thus the new motor makes the same power as the older F20C, simply 500rpms sooner at basically every point on the curve.
• Compression has been bumped up a tenth of a point to 11.1 (from 11.0:1) and the valve timing has been altered to enhance mid-range performance.
• 240hp at 7800 rpm (vs 240hp@8300 rpm) and 162 lb-ft @ 6500 rpm (vs 153 lb-ft @ 7500 rpm).
• This will improve oil consumption and reduce piston noise, Honda improved the cylinder machine honing process by bolting a dummy head to the block (a technique used in race engine building) to improve accuracy. It results in reportedly less than 25% of the deformation on a block.
• The enlarged displacement results in a 6-10% improvement in horsepower and torque from 1000 to 8000 RPMs. Honda claims at the normal operating range of 4500 RPMs the 8 ft-lb torque increase in real world driving translates to 15 ft-lbs over the prior years engine.
• Continues to use traditional VETC instead of iVTEC as on the K-series motors.
• highway gas mileage dropped 1 mpg
• Honda claims better acceleration in each gear, offset only slightly by the reduced top speed potential in each gear (in the older car, thanks to the slightly taller gearing and extra rev capacity, you're able to hold a gear a bit longer, resulting in better acceleration during that brief period where the '04 must up shift while the '00-'03 is able to remain in the lower gear).
• Throttle pedal travel was shortened and pedal effort increased. By reducing the diameter of the throttle body drum, pedal effort is increased approximately 10% at the completely shut end, and 6% at WOT. This was done partly to reduce the occurrence of accidental throttle input such as when the driver encounters a road undulation. Accelerator pedal travel was shortened by approximately 10mm.
• The '03's pistons whiz at 4906 feet per minute at 8900 rpm, whereas the '04's slugs rip along at just 4761 feet per minute at 8000 rpm.

TRANSMISSION
• A tighter secondary gear reduction ratio (1.206 vs 1.16) to provide a bit more snap off the line and to better match the characteristics of the new motor. This is also called the intermediate ratio and is the gear after the transmission and before the driveshaft. It goes like this: Crankshaft --> clutch --> transmission (gears 1-6 + R) --> intermediate ratio gear --> driveshaft --> rear diff --> axles
• 4% shorter ratios for 1st through 4th gears while the 5th ratio is effectively 1% shorter and 6th is effectively 2% longer, for a slightly more relaxed cruise speed. 5th gear ratio changed from 0.971 to 0.942. 6th gear ratio changed from 0.811 to 0.763.
• Carbon fiber synchromesh replace the solid brass ones for all gears except reverse. The new design features a brass ring with a carbon fiber element bonded on the inner surface, resulting in simplified mechanical components, increased synchronizer capacity, improved abrasion resistance, and reduced weight. The weight reduction and increased capacity translates to a smoother and quicker shifting feel. Further enhancing shift feel quality is a reduction in the load acting on the disc spring. Per Honda, this tweak results in reduced shift knob operational load and reduced harshness.
• transmission case rigidity improved

CLUTCH

• Redesigned clutch and clutch case.
• To reduce the "impact torque" of a high rpm clutch dump, the new clutch has an additional orifice at the sleeve cylinder, which reduces the torque reaction acting on the drivetrain, in effect a clutch delay system.
• The clutch case has incorporated additional rib reinforcements to reduce vibrations and noises generated by the drivetrain. The additional ribs have improved clutch case rigidity by approximately 10%.

DIFFERENTIAL
• Redesigned differential; it has been beefed up.
• By moving to an FCD material (from FC), the case rigidity was improved by 40% while the overall case strength was increased 20%.
• Gear fatigue resistance improved by 5% through a change in the shot peening method for the drive pinion gear.

SUSPENSION & STEERING
• Front spring rates increased by nearly 7%
• Rear spring rates were softened by roughly 10%.
• Shock damper rates have been adjusted accordingly.
• Front stabilizer bar is unchanged.
• Rear stabilizer bar was reduced in diameter by 1.8mm to 25.4 mm to improve bump steer & cornering.
• To enhance steering feel and accuracy, the suspension geometry was altered slightly, lowering the steering knuckles by 1.5mm.

One owner’s research found the front suspension received a new front upper arm (left side only); some owner’s speculate that was to correct difficulties in setting the camber on that side. There’s a new part number for the self lock cam nut and bolt at the lower arm’s adjustment point. There’s a new part number for the front lower arm but no apparent geometry change; it’s thought to be a test spec. There are no apparent changes to the front sub frame. The rear suspension received a new knuckle and they moved the mounting point for the control arm. The bushing for the upper arm now has a separate part number; previously it bundled with the part. The tabs for the rear upper arm in rear sub frame have a new part number; it could be durability or geometry change. Front and rear hubs remain the same.

• The EPS (Electrical Power Steering) system features an optimized steer response gain, while the software was updated to improve steering linearity and agility. The steering gear ratio was also changed to match the new suspension and tire characteristics. Increased rigidity of the steering gearbox supporting mounts results in improved steering precision as well.
• One of the "features" of the outgoing S2000's rear suspension was its tendency to exhibit bump steer at the limits. Honda's engineers have attacked this issue from several angles. Rear toe in was reduced from -0deg 19' to -0deg 10'. At a 50mm bump deflection, toe-in has been reduced from -0.19 degrees to -0.05 degrees. Secondly, the rear roll center was lowered from 101mm to 92mm. Honda claims improved roadholding under full suspension compression or during severe body roll situations.
• Honda claims improvements in overall stability, steering accuracy/effort/feel, bump steer characteristics, wet performance/hydroplaning, high-speed stability, smooth ride comfort, choppy ride comfort, and at the limit controllability.
• steering wheel lock-to-lock increased from 2.4 to 2.6 wheel turns.
• steering ratio lowered from 13.8:1 to 14.9:1

CHASSIS
• Chassis code AP1 = MY00-MY03 chassis changed to AP2 with the re-designed bumpers and new headlights / tail lights.
• A new cross brace at the very front of the frame (positioned horizontally, in front of the radiator),
• Reinforcements at key crossmember joints
• Additional fixing points to existing braces
• Reinforcements to the rear wheel arch bulkhead
• Front suspension upper arm brackets were strengthened, further benefiting handling.
• overall weight increase of 25 pounds, from 2810 to 2835 pounds

WHEELS & TIRES
• New 17" wheels, wider in front and rear (by 0.5" and 1.0" respectively), wrapped in wider tires.
• In the front, 205/55R16s were replaced by 215/45R17 tires.
• In the rear, 245/40R17s bumped the incumbent 225/50R16s.
• Honda says both changes are key contributors to extended cornering limits.
• The tires are now Bridgestone Potenza RE050s, replacing the former model's Bridgestone Potenza S-02s.
• The new tires feature a completely different tread pattern, intended to improve the balance in performance between dry and wet conditions.

BRAKES
• To improve fade resistance and stopping power at and near the limit, the brake pad material has been changed from a non-metallic compound to a new metallic compound. The new pad material (Jurid632) provides greater frictional stability in high-temperature operating ranges.
• Master cylinder ratio has been changed from 6.5 to 6.0, resulting in an increased feel of rigidity and "build-up" quality (Honda's term for more stopping power in the latter stage of brake application under constant application). Honda claims less pedal travel is required than previously.
• The ABS system has been improved through the use of split-regulation yaw-control logic for improved stability on split-μμ surfaces when the ABS is triggered. Furthermore, though more powerful than before, the system (consisting of the CPU and modulator) has been downsized for both precious space and weight savings.

EXTERIOR
• new nose job, with wider air intake and new headlights above it
• fake brake opening reshaped and moved inward
• new HID headlights using projector beams
• new LED taillights
• lower appearing rear bumper
• reshaped exhaust pipes, now oval
• spiral double horn unit replaces the current flat double horn.
• new color - Rio Yellow Pearl
• Spa Yellow dropped

INTERIOR
• new combination red and black colored seats
• more sculpted door panel inserts; shoulder room increased by 0.5"
• wave ignition key to make copying it more difficult
• reshaped steering wheel
• new tweeter and mid range speaker housings
• metallic-look trim
• new center console with two beverage holders
• dash changes including a new gauge cluster, reshaped roll where the start button and radio controls are located
• restyled aluminum finish.

FIRST COMPARISON
Sport Compact Car magazine did a road test of the 2004 S2000. They report the 2.2 liter made 210 hp at 8000 rpm at the rear wheels, compared to 203 hp at 8500 rpm that the old 2 liter delivered, and 146 lb-ft of torque at 6400 rpm, compared to 136 lb-ft at 6300 rpm. They go on to say, “Sure, peak power remains the name of the game here, but there's obviously more power than Honda is telling us, and the improved midrange is nice to have around town”. They also did some handling tests and reported the 04 understeered on the skid pad; it registered .89 compared to .92 for the 2 liter car. In the slalom the 04 improved by 1.2 mph to 71.0 mph. They also did some acceleration runs but fried the clutch. 50 to 70 acceleration was faster by .18 seconds, and 0 to 100 is faster by just .2 seconds.

Model Year 2005

Per 9/1/04 Honda press release “There are no changes to the 2005 Honda S2000.”

• On 2/15/05 the MSRP went from $32,950 to $33,150. Shipping is another $515.

Model Year 2006

The 39th Tokyo Motor Show, held from October 22 to November 6, 2005, at Makuhari Messe in Chiba, Japan, had dozens of cars and motorcycles on display, but it is the new S2000, equipped with even more advanced features than ever before, that shared the Motor Sports Zone stage with a rare close-up look at Honda’s F1 and IndyCar Series racers.

• MSRP increased to $34,050 and shipping to $550 for a total of $34,600.
• Drive-By-Wire Throttle System. Use a computer sensor to input throttle as opposed to pulling on the throttle cable
• Vehicle Stability Assist (VSA) with traction control. A combination of computer controlled throttle and individual wheel braking to control sudden changes in vehicle behavior. VSA has a turn-off switch where the defrost button (moved) used to be.
• 20 lbs heavier
• Redesigned road wheels
• Redesigned steering wheel
• New color, Laguna Blue
• Daytime running lights (DRL)
• Brake Assist, which helps drivers apply full braking pressure in an accident avoidance situation via the ABS actuator. Braking pressure is maintained momentarily after the driver's initial braking action to help the driver stop promptly. It deactivates when the driver releases pressure on the brake pedal
• Basic warranty is 3 year/36,000 but the power train was extended to 5 years/60,000 mile
• Exterior temperature gauge
• New seats; they no longer have seat back pocket and headrest speaker system is gone
• 4 of the 8 speaker audio system are integrated roll bar speakers
• Sebring silver and white only come with a black interior
• CARB emissions rating is now LEV-2
• Passenger-side airbag cutoff
• IAC Valve has been eliminated, along with the cruise control hardware; it is all controlled by the ECU for the DBW system. A gas pedal cable runs into the engine compartment to an actuator. From there it's electronic.
• New intake manifold, intake support bracket, and injector cover
• Only one cam sensor
• New style map sensor
• IAT sensor has moved to the rubber intake tract
• Differential now has a breather box mounted behind it
• Fuel line at engine is now a quick-release type
• Air pump, associated lines and control valve, have been eliminated
• Weight/and or/position sensors mounted in the seats
• Fan switch in the radiator has been replaced with a second CTS, in turn the fans are now computer controlled
• HO2S in the header is now referred to as an Air fuel ratio sensor
• If you leave the gas cap loose, you'll get a "CHECK GAS CAP" warning, displayed in the outside temp display
• NOT SURE ON THIS: In Europe they are advertising a new three-part speedster cover. The cover fits over the folded hood and features a pair of raised domes that sweep back from the two headrests/rollover bars to provide a distinctive look reminiscent of many classic sports cars.
• HP is now stated at 237 - due to the auto industry wide change in how HP is calculated*
I was going to say a gay joke. Butt fuck it.
Obrazek
Avatar użytkownika
insane
Klubowicz redliner
 
 
Posty: 2428
Dołączył(a): 2008-10-21, 23:49
Lokalizacja: Poznań

Re: Różnice modeli S2000 w poszczególnych latach produkcji

Postprzez hlorek » 2014-06-10, 18:58

Też się w to wczoraj wczytywałem jak okazało się że servo i pompa nie są takie same w poszczególnych rocznikach. Przy każdym kolejnym lifcie "rozmiękczano" eskę poprzez zmianę zawieszenia, stabilizatorów, dodaniu asystentów (w 2006 wprowadzono nawet asystenta hamowania) aby na koniec dać wersję CR. Gdyby tak pozbierać najlepsze elementy z poszczególnych lat produkcji (krótkie przełożenie układu kierowniczego, krótki dyfer, f20 jdm itd, zawieszenie i aero z CR) to powstałaby zupełnie seryjna supereska :>
Avatar użytkownika
hlorek
 
 
Posty: 1103
Dołączył(a): 2009-04-08, 12:35
Lokalizacja: Gdynia/Reda/Wejherowo
Rocznik S2000: 2004
Wersja: AP2

Re: Różnice modeli S2000 w poszczególnych latach produkcji

Postprzez skuri » 2014-09-21, 12:11

Pytanie. W polifcie 04/05 z tego co zauważyłem (a może to AP1/AP2 ?) dwa rodzaje OEM wydechów. Jedna mają charakterystyczne kolanka(jak w przedliftach) przy końcowych a inne nie.W czym różnica ?
Avatar użytkownika
skuri
 
 
Posty: 155
Dołączył(a): 2013-08-21, 10:43
Rocznik S2000: 2001
Wersja: AP1

Re: Różnice modeli S2000 w poszczególnych latach produkcji

Postprzez s2000 » 2014-09-21, 19:02

Polifty tez maja te kolanka, nie ma ich tylko wersja CR.
s2000
Klubowicz 2k rpm
 
 
Posty: 248
Dołączył(a): 2012-04-19, 10:21
Rocznik S2000: 2004
Wersja: AP1


Powrót do FAQ

Kto przegląda forum

Użytkownicy przeglądający to forum: Brak zalogowanych użytkowników i 1 gość